![]() ![]() As mentioned, once I see "Ready" (Paper about 1/4" ahead of that black presser bar (with all the little springs) it's set to go. Problem is always getting ti to feed 1/4" ahead of that long black presser bar without getting the "SKEW" error message. I just set some flat board across the back tray into the rear feed slot and lay the paper on it and let it pull in. ![]() I can feed 17 inch rolls I cut down into 38" lengths into the rear feed slot. It'll say User Defined or show the User Defined and "Saved" size like 17 x 25.5 or similar. If it accepts your size values and back out of it, the main Epson window won't flip out and report a size of 4圆 inches too. I think a lot trim down to 16" widths and use the less stubborn front feed slot, but the back slot takes the 17 inchers. You have to set it slightly less than 17 inches as it won't do borderless at that size (That I have yet found.). I made a few special entries in there for 17 x 22 and 17 x 25.5 inch papers (I prefer the 17 x 25.5 as it is the 2:3 ratio (35mm) off the FX sensor size) and some 16.25 x 36.5 panorama thing I also entered. ![]() If you look in the "User Defined" area in the Epson 3880 driver pane, it says something about 17 x 37.5 inches as the maximum size. If that leader comes off, and you got tape wrapped up inside the printer, you got a major dismantling mess on your hands to get it all out of the feed and roller system. Whomever came up with that idea of "taping a paper leader to the front of the canvas" and using it to feed into the machine should be thrashed. Reload." if I see "Ready" after my forcible paper tug to make the paper straight and parallel to the print head travel and paper presser arm, I'm good to go. ![]() This is with the "stubborn" rear feed slot (That often reports "SKEW" errors.) with canvas and matte ink if it matters.Īside, I found to keep from having feed issues with the rear slot and canvas, if I open the top black door and see the paper auto-feed to about 1/4" ahead of the black spring loaded presser are that extends the width of the paper, and make sure the 1/4" is the same on both sides as the printer head scans the paper edge for evenness, I can tug the canvas paper back on a side to even it before the head fully parks and reports back "SKEW Error. However, once coming out of the printer, it is cropped off by 2 inches at the top, but the length is correct and not cropped? Measures 14 x 36.75 inches.ĭon't know why the page shows the correct dimensions, and it looks right on the screen, but the printer's output doesn't match. Image looks correct in QU and it shows the dimensions correct as well. Innovative “dynamic” color profiles ensure full control over color mixture and ink consumption combined with perfect print quality.I successfully set up a panorama in QU and the Epson 3880 menu for 16.25 x 36.75 inches (QU shows 16.266 x 36.766 fwiw). PrintFab is the printer driver with RIP (Raster Image Processor) functionality. The time has come for independent printer drivers - better performance and more freedom for your printer! Nozzle test print, Print head cleaning, Test page License PrintFab Home L / PrintFab Pro required to use the maximum print size Plain paper, Epson Inkjet Paper, Archival Matte, Epson Matte Heavy, Epson Photo Glossy, Epson Premium Glossy, Epson Premium Satin, Epson Ultra Glossy, Transparency (multifunction devices: only printer unit is supported, not scanner unit)Įpson WorkForce WF-7210 - Windows printer driver features PrintFab License The perfect printing solution for your Epson WorkForce WF-7210 printer ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |